Put a thin bead of silicone around the bottom lip of the sink and set it into the hole. Clean up any excess silicone or smooth a line. Depending on the design of the sink and the opening where it connects to the plumbing lines, you may need to caulk in any number of different places. Secure the sink with clips. Connective clips are often included with new sinks to help anchor the units into place, in addition to the sealing caulk. The design of this varies, and will depend on the type of sink and the design, but they usually act like a lever to hold the sink in place.
Follow the instructions included with the new sink and defer to the manufacturer's guidelines. Install the faucet. New faucets usually screw onto the faucet assembly in a clockwise direction. Some faucets will have a rubber gasket around the base, and screw on easily, while others will recommend using silicone sealant to secure to the sink or counter. You can anchor the faucet by reaching up underneath and using lock nuts that are included with the installation kit.
Make sure the space for the faucet matches the location of the sink, using the template to measure before you install anything.
Install the tailpiece and drain kit. Drop the tailpiece through the sink and screw on the tailpiece nut from underneath.
Some sinks come with gaskets that go between sink and tailpiece. If it doesn't, use non-hardening plumbers' putty or silicone to create the seal. Install the gasket, the included cardboard washer, and the locknut to secure the tailpiece.
Part 3. Make sure the water lines match the new fixture. If you put two pipe threads together, splice them with teflon tape. Connect the water supply lines.
Water supply lines should screw into place with the corresponding joints on the new faucet. The specific size of the connectors should be included in the instructions for the specific faucet that you're installing. Lines also need to be long enough so you won't put stress on the joints. Better to have extra long lines and have them loop. No hard bends or kinks. Make them hand tight, and somewhere around a quarter to half turn with a wrench. Usually the "female" connection piece on both ends will always have rubber gaskets, so you don't need teflon tape.
Connect the pop-up. The pop-up is the device that allows you to open and close the sink drain, usually made of a simple metal rod with ball attached to it. Drop stopped into sink from top, slide short end of rod into the opening on the tailpiece, making sure that the opening for the ball is facing toward the lever for the pop-up. Install as per the instructions. Sometimes you need washers and sometimes you don't.
Slide nut to trap the ball in the tailpiece. Tighten so there's no wiggle, but not so tight that it's difficult to raise and lower. Attach thumbscrew to pop-up lever rod while sliding the rod from the ball so they can attach and allow you to screw together. Seal your connections with silicone caulk. Finish with silicon around the top of the sink, anywhere that the basin of the sink meets the wall, filling any gaps with a thin bead of caulk. Let the caulk dry for about 24 hours before turning on the water and going back over your work to check for leaks.
Turn on the water and check for leaks. There's no way to know if something is going to leak until you turn the water on. If you have small leaks from the rubber connections, try tightening more.
The drain itself will also sometimes leak, which can be caused by over-tightening and straining the seal created by the connector gaskets. If that's leaking, don't go past hand tight.
Installing a kitchen sink is something most DIYers can handle with basic tools and a few supplies. Most kitchen sinks range between 8 and 10 inches in depth. While a deeper sink may make it easier to soak and pile up dishes, it can make it harder for shorter family members to use. Luckily, most sinks come with a paper template that you can tape onto the counter to use as a cutting guide. Use a jigsaw to drill along the line from corner to corner. Although some people still like double sinks, they were designed for a time when few people had dishwashers.
Now that most homes have dishwashers, single sinks are more popular. Disclosure: BobVila. You agree that BobVila.
All rights reserved. Expert advice from Bob Vila, the most trusted name in home improvement, home remodeling, home repair, and DIY.
Kitchen How to Install a Kitchen Sink in 10 Easy Steps It is possible to install a kitchen sink without destroying your countertop, and a DIYer with average skills can complete the replacement in about 4 hours. Connect with a kitchen expert.
Find licensed kitchen design and construction pros in your area and receive free, no-commitment estimates for your project. Find Pros Now. Immediately push pieces together. Hold for 30 seconds. Attach the dishwasher drain line to the waste nib of the tailpiece.
Tighten the hose clamp with a screwdriver. Remove the aerator from the faucet and run the water full blast. Look for leaks at all connections along the supply and drain lines.
In case of leaks, carefully tighten the nuts by one-eighth turns until the leak stops. Make sure the sink's front edge is parallel to counter's edge. Fill the sink with water to weigh it down and hold it tight overnight as the caulk sets. Cookie banner We use cookies and other tracking technologies to improve your browsing experience on our site, show personalized content and targeted ads, analyze site traffic, and understand where our audiences come from.
By choosing I Accept , you consent to our use of cookies and other tracking technologies. How to Install a Kitchen Sink. By Jefferson Kolle. Pinterest Email Pocket Flipboard. Person holding a new faucet above a kitchen sink. Mark the center of the sink on its back lip.
Trace around the sink, then remove it. Stuck and you have no idea on how to go about installing a kitchen sink? Worry no more! This step-by-step easy guide will help you in installing your best kitchen sink. If you are installing your sink in your new kitchen or just trying to fix some broken parts, then you need to install a functional drainage system. Just learn how to install a kitchen sink drain pipe and you will be good to go.
The kitchen sink is an important part of any household as it is where food is disposed of, flower vases are filled, dishes are washed, and the food is prepared. There are various ways of installing a kitchen sink. You can either install it below the counter, above the counter or as part of the counter depending on the sink style you decided to purchase.
In this guide, I will be showing you everything that you need to know when installing a kitchen sink. The set of instructions will cover the installation process right from creating a hole to fixing the faucets and drain in the kitchen. You need to begin with selecting a suitable type of sink for replacing an old worn out kitchen sink or maybe one for your new kitchen.
When it comes to choosing a sink, there are a variety of sinks to choose from and you can follow the considerations suggested in this post What You Should Consider Before You Buy a Kitchen Sink. Therefore, you should only pick one with the design that you like. Double bowl sinks and single drop-in sinks can fix well on a variety of countertop surfaces, which makes them a suitable option to consider. Under mount sinks , on the other hand, are installed beneath the counter.
This means that they are only ideal for use in engineered or natural stone countertops and solid-surfaces. Begin with measuring place to mount the sink to ensure that it will correctly fit. If you are repairing, then you can take the measurements of the old sink. If the drain unit is smaller than the size of the new sink, then you need to make some adjustments to the plumbing and the countertop opening. To ensure that you achieve maximum precision before installing a kitchen sink, you might find drawing your old sink and record all its measurements, which entails the measurements of the length between the drain centers to the sink wall quite helpful when out shopping for one.
Alternatively, you can remove the sink you are replacing and carry it when you are going to buy the new sink to help you in selecting the right replacement unit. However, you should ensure that your safety is enhanced by putting on protective glasses when cutting the pipe or performing operations under the sink to avoid exposing yourself to danger.
0コメント